Trucker Forum - Trucking & Driving Forums - Class A Drivers

Trucker Forum - Trucking & Driving Forums - Class A Drivers (https://www.classadrivers.com/forum/)
-   New Truck Drivers: Get Help Here (https://www.classadrivers.com/forum/new-truck-drivers-get-help-here-102/)
-   -   Downshifting (https://www.classadrivers.com/forum/new-truck-drivers-get-help-here/32429-downshifting.html)

Stryperz 02-16-2008 05:03 PM

Downshifting
 
im looking to get my CDLs and start a new career...ive signed up with Schneider to go to Charlotte hopefully 3/15....im trying to get a headstart with driving here at work... i work in a warehouse and run the docks but occasionally i get to drive a switcher truck and since ive gotten my learner's permit ive tried driving one of the mack's that we use to go between plants that are a couple miles apart....i dont any issues up shifting but its the downshifting that im having a diffucult time doing.. are there any tricks to it ??? if anyone could give any suggestions I would definately appreiciate it.. Thanks!!!!

Binder 02-16-2008 05:21 PM

Takes practice .

Match the RPM to speed .

Kick up the RPM about 200 to 400 and then shift .
You just have to learn to watch the tech , until it becomes natural .

terrylamar 02-16-2008 05:31 PM


Originally Posted by Binder
Takes practice .

Match the RPM to speed .

Kick up the RPM about 200 to 400 and then shift .
You just have to learn to watch the tech , until it becomes natural .

It actually works much better when you watch the tach. 8)

Stryperz 02-16-2008 09:57 PM

I keep tryin... but its not working out very well...guess im not holding my tongue right ....maybe tomorrow night I can ride with someone for a few hours and watch them and see how they do it.....

scania 02-16-2008 11:44 PM

You're not rapping out on the next gear up are you?

Stryperz 02-16-2008 11:56 PM

i dont believe so... couple of the full-time switchers that use the mack's regularly say that the ones we have are difficult to learn on.... i believe them :lol:

Fredog 02-17-2008 01:12 AM

Re: Downshifting
 

Originally Posted by Stryperz
im looking to get my CDLs and start a new career...ive signed up with Schneider to go to Charlotte hopefully 3/15....im trying to get a headstart with driving here at work... i work in a warehouse and run the docks but occasionally i get to drive a switcher truck and since ive gotten my learner's permit ive tried driving one of the mack's that we use to go between plants that are a couple miles apart....i dont any issues up shifting but its the downshifting that im having a diffucult time doing.. are there any tricks to it ??? if anyone could give any suggestions I would definately appreiciate it.. Thanks!!!!

I hope I can say what I am trying to explain, example.. if you go from 6 to 7 at 35 mph and 1900 rpm ( just made up numbers) then when you downshift from 7 to 6 you would do it at the same speed and rpm. so you would get down to 35 mph, push the clutch in, rev it to 1900 and shift into 6. I hope you can figure out what I'm trying to say, it's hard to figure out how to say it.

Kranky 02-17-2008 01:22 AM

If it's an older Mack with a 5 or 6 speed transmission, then there is about 900 RPM's between gears.

If you're trying to downshift one of those by raising the RPM's by 400 RPM it ain't gonna work.

Fredog 02-17-2008 01:51 AM


Originally Posted by Splitshifter
If it's an older Mack with a 5 or 6 speed transmission, then there is about 900 RPM's between gears.

If you're trying to downshift one of those by raising the RPM's by 400 RPM it ain't gonna work.


the old 5 speed maxidynes were something else, the first one I drove the boss said wind it up, kick it onto neutral, count to 100 then hit the next gear, he wasnt far off :D :D

Binder 02-17-2008 11:49 AM


Originally Posted by terrylamar
It actually works much better when you watch the tach. 8)

:oops: Beer and typing don't mix !


All times are GMT -12. The time now is 11:41 AM.


Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved